Paint Removers  Wood Preservatives  Medical Supplies   Concrete Materials
Safety Sheets  Contact Us  How to Buy  Visit The Furniture Guy  History  Home

BACK

EFFECTIVE DATE: 12/01/94

SECTION 1 - PRODUCT IDENTIFICATION

Product Name:
Plasticure (Solvent Based)

Chemical Name:
Aqueous Petroleum Hydrocarbon Resin emulsion

Formula:
Proprietary

Trade Name and Synonym:
Plasticure Water Base

Chemical Family:
Aqueous Petroleum Hydrocarbon Resin Emulsion

CAS Number:
None

Emergency #: 1-800-535-5053

SECTION 2 - COMPONENTS

INGREDIENT		OSHA HAZARD
Surfactant 9		Eye irritant
Water 91

SECTION 3 - PHYSICAL DATA

Boiling Point	For product	350 Deg F
Vapor Pressure	For product	Not Available
Specific Vapor Density		Not Available
Specific Gravity		H20=1 .820
Percent Volatile		0
Evaporation Rate	n-Bu Acetate=1	Not Available

SECTION 4 - FIRE AND EXPLOSION INFORMATION

FLASHPOINT:
Not Applicable

EXTINGUISHING MEDIA:
Water spray to cool exposed surfaces

HAZARDOUS DECOMPOSITION PRODUCTS:
No unusual.

FIREFIGHTING PROCEDURES:
If this material is located in a fire area, use water spray to cool exposed surfaces. Foam, dry chemical, carbon dioxide, or water spray may be used to extinguish fires.

SPECIAL FIRE AND EXPLOSION HAZARDS:
None.

SECTION 5 - HEALTH HAZARD DATA

EFFECTS OF OVEREXPOSURE

EYES:
Irritating, and may injure eye tissue if not removed promptly.

SKIN:
Low order of toxicity.

INHALATION:
Negligible hazard at ambient temperature (-18 to 38 Deg C; 0 to 100 Deg F).

INGESTION:
Minimal toxicity.

FIRST AID

EYE CONTACT:
Flush eyes with large amounts of water until irritation subsides if irritation persists, get medical attention.

SKIN CONTACT:
Flush with large amounts of water; use soap if available. Remove grossly contaminated clothing, including shoes, and launder before reuse.

INHALATION:
Using proper respiratory protection, immediately remove the affected victim from exposure. Administer artificial respiration if breathing is stopped. Keep at rest. Call for prompt medical attention.

INGESTION:
First aid is normally not required.

SECTION 6 - REACTIVITY DATA

HAZARDOUS POLYMERIZATION:
Will not occur

STABILITY:
Stable

INCOMPATIBILITY:
None.

SECTION 7 - SPILL OR LEAK PROCEDURES

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
Contain spills and absorbs with inert material. Place in DOT drum.

WASTE DISPOSAL METHOD:
Dispose of all waste in accordance with Federal, State and Local agencies by a state approved waste hauler.

SECTION 8 - SPECIAL PROTECTION INFORMATION

PERSONAL PROTECTION:
For open systems where contact is likely, wear long sleeves, chemical resistant gloves, and chemical goggles. Where contact may occur, wear safety glasses with side shields. Where overexposure by inhalation may occur and engineering, work practice or other means of exposure reduction are not adequate, approved respirators may be necessary.

VENTILATION:
Maintain ambient concentrations below recommended exposure limits.

SECTION 9 - SPECIAL PRECAUTIONS OR OTHER COMMENTS

OTHER HANDLING & STORAGE CONDITIONS

Store at 40 Deg F to 180 Deg F to maintain quality. Avoid

freezing product.

PROTECT FROM FREEZING:
Keep containers tightly closed to prevent formation of dried film. If film does form, product should be filtered before use.

The information accumulated herein is believed to be accurate but is not warranted to be whether originating with Green's Products or not.

[PAINT REMOVERS]  [WOOD PRESERVATIVES]  [MEDICAL SUPPLIES]   [CONCRETE MATERIALS]
[SAFETY SHEETS]  [CONTACT US]  [HOW TO BUY]  [VISIT THE FURNITURE GUY]  [HOME]